Aluminum Sheets are a rectangular section product, with thickness from 0.15 mm to 6.35 mm. Plates are rolled products with a minimum thickness of 6.30 mm. These are produced by cold rolling. In some instances, one or more annealing stages are required

Typical Applications

Application in conversion processes

Standard Format

Rolls and strips

Applicable Standards
Aluminum Standards and Data,
The Aluminum Association.

ASTM B-479.

Relevant Characteristics

• High Flexibility.

• Our lubricants comply with the following regulations of U.S. Food & Drug Administration:
21 CFR 178.391 Rolled sheets and foil.
21 CFR 172.884 Direct food additives.
21 CFR 178.365 Indirect contact with food.
21 CFR 178.362(b) Indirect contact with food.

• Machine finishing (polished on both sides) and Matt Polished finishing. (Upon request and verification of orders).

 

All tolerances conform to Standard AA. However, the plant is able to provide narrower tolerances in some cases (including 1/2 ASTM or AA), previous verification of orders

Issue: April 2003

Product and Dimensional Limits

       

 

 

 

 

 

 

WIDTH SPECIFI-
CATION
(mm)

TOLERANCE (±)

THICKNESS SPECIFI-
CATION
(mm)

TOLERANCE (±)

FOR THICKNESS OF LESS THAN 6.30 (± mm)

FOR THICKNESS GREATER THAN 6.30 (± mm)

FOR WIDTHS UP TO 1000
(mm)

FOR WIDTHS EXCEE-
DING 1000
(mm)

400-500

2.50

7.00

3.40 – 4.00 INC.

0.14

0.22

4.00 – 5.00 INC.

0.18

0.26

500-1000

3.00

8.00

5.00 – 6.30 INC.

0.24

0.32

6.30 – 8.00 INC.

0.32

0.40

1000- 1220

3.50

9.00

8.00 – 9.00 INC.

0.44

0.46


     

 

 

 

 

LENGTH
SPECIFICATION
(mm)

TOLERANCE (±)

MACHINE FINISHING

FOR
THICKNESS OF LESS THAN 6.30 (mm)

FOR THICKNESS GRETER THAN 6.30 (mm)

600 - 1000

2.50

8.00

THICKNESS:
FROM 3.40 mm
TO 9.0 mm
WIDTH: FROM 400 mm
TO 1220 mm
LENGTH: FROM 600 mm
TO 3360 mm

1000 - 2000

3.00

9.00

2000 - 3000

3.00

10.00

3000 - 3360

3.50

10.00

Mechanical Properties

 

 

 

 

 

 

 

 

ALLOY

TEMPER

TENSILE STRENGTH (Kg/mm2)

ELASTIC LIMIT (Kg/mm2)

ELONGATION % *

THICKNESS SPECIFICATION (mm)

MIN.

MAX.

MIN.

3.20
4.00

4.20
6.30

6.30
9.00

1050
1145
1350

O

5.6

9.7

-

 

30

 

H12

8.2

11.7

-

 

8

 

H14

9.7

13.3

-

 

5

 

H16

11.2

14.8

-

4

 

 

H18

12.7

-

-

 

 

 

1060
1070

O

5.6

9.7

1.5

 

25

 

H12

7.6

11.2

6.1

 

12

 

H14

8.7

12.2

7.1

 

10

 

H16

9.7

13.3

7.6

5

 

 

H18

11.2

-

8.7

 

 

 

F

7.2

 

-

 

 

 

1100

O

7.6

10.7

2.5

 

30

 

H12

9.7

13.3

7.6

 

8

 

H14

11.2

14.8

9.7

 

5

 

H16

13.3

16.8

11.7

4

 

 

H18

15.3

-

-

 

 

 

H19

16.9

-

-

 

 

 

F

10.0

-

-

 

 

 

3003

O

9.7

13.3

3.6

 

25

 

H12

12.2

16.3

8.7

 

6

 

H14

14.3

18.4

11.7

 

5

 

H16

16.8

20.9

14.8

4

 

 

H18

18.9

-

16.8

 

 

 

H19

20.4

-

16.5

 

 

 

3105

O

9.8

14.8

2.51

 

20

 

H12

13.3

18.4

10.7

 

 

 

H14

15.3

20.4

12.7

 

 

 

H16

17.3

22.4

14.5

 

 

 

H18

19.4

-

16.8

 

 

 

* FOR REFERENCE ONLY.

Chemical Composition and Standard Designation

 

 

 

 

 

 

 

AA
Designation

Silicon

Iron

Copper

Manga-
nese

Magne-
sium

Chro-
mium

1050

0.25

0.40

0.05

0.05

0.05

-

1060

0.25

0.35

0.05

0.03

0.03

-

1070

0.20

0.25

0.04

0.03

0.03

-

1100

0.95 Si + Fe

0.05-0.20

0.05

-

-

3003

0.6

0.7

0.05-0.20

1.0-1.5

-

-

3105

0.6

0.7

0.30

0.30-0.8

0.20-0.8

0.20


 

 

 

 

 

 

 

AA
Designation

Nickel

Zinc

Titanium

Other

Aluminum

C/U

Total

1050

-

0.05

0.03

0.03

-

99.50

1060

-

0.05

0.03

0.03

-

99.60

1070

-

0.04

0.03

0.03

-

99.70

1100

-

0.10

-

0.05

0.15

99.00

3003

-

0.10

-

0.05

0.15

Remaining

3105

-

0.40

0.10

0.05

0.15

Remaining

VALUES SHOWN REFER TO THE MAXIMUM PERCENTAGE BY WEIGHT ALLOWABLE BY ELEMENT, EXCEPT WHEN A DIFFERENT RANGE IS ESTABLISHED OR WHEN EXPLICITLY DEFINED OTHERWISE.