Embossed aluminum sheet manufactured using a continuous cast mill process and a sequence of cold rolling passes. In some instances, additional intermediate annealing stages and final rolling passes are required.

Typical Applications

Decorative articles for architecture and transportation. Applications in refrigeration.

Standard Format
Embossed Rolls.

Embossed Sheets

Applicable Standards
Aluminum Standards and Data,
The Aluminum Association.

ASTM B-209.

Relevant Characteristics

• High resistance to corrosion.

• High ductility in soft temper.

• Good forming capacity.

• High thermal conductivity.

• High mechanical strength

 


All tolerances conform to Standard AA.

Product and Dimensional Limits for Embossed Aluminum Roll

 

 

 

 

 

 

 

WIDTH
SPECIFICATION
(mm)

TOLE RANCE
(±)

THICK NESS
SPECIFICATION
(mm)

TOLE-
RANCE
(±)
(mm)

SURFACE
TYPE

DIAMETERS

EMBOSSED

INSIDE

MAX.
OUTSIDE

9.70 – 150 INC.

0.25

0.500 – .630iNC.

0.050

STUCCO
(MAX. WIDTH 960mm)
GRID
(MAX. WIDTH 940 mm)
STRIPED
(MAX. WIDTH940 mm)

406 O 508 mm
FOR
STRIPS
OF UP
TO
100
mm
(WIDTH):
406
mm

860
mm

150 – 250 INC.

0.50

0.630 – .800iNC.

0.060

250 – 750 INC.

1.00

0.800 – 1.00 INC.

0.070

1.000 – .200INC.

0.080

750 – 960 INC.

1.00

1.200 - 1.600INC.

0.08

1.600 – 1.65 INC.

0.09

Embossed Aluminum Sheet

Product and Dimensional Limits

         

WIDTH
SPECIFI-
CATION
(mm)

TOLE-
RANCE
(±)

THICKNESS
SPECIFI-
CATION
(mm)

TOLE-
RANCE
(±)

LENGTH
SPECIFI-
CATION

TOLE-
RANCE
(±)

SURFACE
TYPE

EMBOSSED

200 – 250INC.

0.50

0.500 - 0.630 INC.

0.050

200 – 1000INC.

2.00

THICKNESS:
FROM 0.500 TO 1.65mm
WIDTH:
STUCCO (MAX. WIDTH 960 mm)
GRID (MAX. WIDTH 940 mm)
STRIPED (MAX. WIDTH 940 mm)

0.630 - 0.800 INC.

0.060

250 – 750 INC.

1.00

0.800 - 1.00 INC.

0.070

1000 – 2000INC.

2.500

1.000 - 1.200 INC.

0.080

750 – 960 INC.

1.00

2000 – 3000INC.

3.00

1.200 - 1.600 INC.

0.08

3000 – 3660 INC.

3.00

1.600 – 1.65 INC.

0.09

Mechanical Properties

 

 

 

 

 

 

 

 

ALLOY

TEMPER

TENSILE
STRENGTH
(Kg/mm2)

ELASTIC
LIMIT
(Kg/mm2)

ELONGATION % *

THICKNESS
SPECIFICATION (mm)

MIN.

MAX.

MIN.

0.50
0.63

0.63
1.20

1.20
1.65

1100

O

7.6

10.7

2.5

17

22

30

H12

9.7

13.3

7.6

3

5

8

H14

11.2

14.8

9.7

2

3

5

H16

13.3

16.8

11.7

2

3

4

3003

O

9.7

13.3

3.6

20

22

25

H12

12.2

16.3

8.7

3

4

6

H14

14.3

18.4

11.7

2

3

5

H16

16.8

20.9

14.8

2

3

4

3105

O

9.8

14.8

2.51

16

19

20

H12

13.3

18.4

10.7

1

2

3

H14

15.3

20.4

12.7

1

2

2

H16

17.3

22.4

14.5

1

1

2

N/A = NOT APPLICABLE.
* FOR REFERENCE ONLY.

Chemical Composition and Standard Designation

 

 

 

 

 

 

 

Designation

Silicon

Iron

Copper

Manga-
nese

Magne-
sium

Chro-
mium

AA

1100

0.95 Si + Fe

0.005-0.20

0.05

-

-

3003

0.6

0.7

0.05-0.20

1.0-1.5

-

-

3105

0.6

0.7

0.30

0.30-0.8

0.20-0.8

0.20

Designation

Nickel

Zinc

Titanium

Other

 

Aluminum

AA

C/U

Total

1100

-

0.10

-

0.05

0.15

99.00

3003

-

0.10

-

0.05

0.15

Remaining

3105

-

0.40

0.10

0.05

0.15

Remaining

VALUES SHOWN REFER TO THE MAXIMUM PERCENTAGE BY WEIGHT ALLOWABLE BY ELEMENT, EXCEPT WHEN A DIFFERENT RANGE IS ESTABLISHED OR WHEN EXPLICITLY DEFINED OTHERWISE.